BEARCAT 800XLT MANUAL PDF

Uniden Bearcat xlt Scanner Manual. Document for Uniden Bearcat xlt Scanner Manual is available in various format such as PDF, DOC. [PDF] [EPUB] Bearcat Xlt Scanner Manual [PDF]. Book file PDF easily for everyone and every device. You can download and read online. Scanner Manual PDF or Read Uniden Bearcat Xlt Scanner Manual PDF on The Most Popular. Online PDFLAB. Only Register an Account.

Author: Kagadal Shaktitaur
Country: Tanzania
Language: English (Spanish)
Genre: Sex
Published (Last): 27 December 2010
Pages: 107
PDF File Size: 5.45 Mb
ePub File Size: 7.15 Mb
ISBN: 514-8-41331-469-7
Downloads: 70973
Price: Free* [*Free Regsitration Required]
Uploader: Tekus

You can also temporarily lockout cancel any combination of these alerts. All trunked systems need at least one site to enter trunking frequencies. While in Review Location Mode: Conventional channels within the groups are scanned in order of creation. The range is typically miles, depending upon the terrain and many other factors. Set Priority conventional only. The default setting is 2 seconds. To Create a Site press Menu. Make sure that the cable terminates in a female, 9-pin serial connector and you select the correct baud rate bps for the rear serial port.

Enter the new frequency and press Hold. Channel- a programmed frequency or talk group ID location. Conventional systems operate similarly, but all unlocked channels are bearcst at least one time regardless of the hold time setting. Press to toggle the lockout status of a frequency in Search Mode. Beracat you program a channel as NFM that is transmitting in FM mode, the audio will sound too loud as compared to correctly programmed channels.

To check for a repeater frequency press then press and hold 8 Rev.

Read uniden-bearcatxlt-scanner-manual

This lets many users share a single frequency, and decreases interference caused by distant transmitters on the same channel. If the ‘Close Call Hits’ system has no frequencies, the scanner does not scan the system.

  AT&T UVERSE 2WIRE ROUTER MANUAL PDF

The quick key for the system must be turned on if one is assigned to the system and not locked out to select the system to store frequencies in otherwise you will see ‘ Nothing to Scan ‘. The default setting is ‘ Unlocked ‘. You can also lock out this home repeater ID so you will not receive it. Point of Interest POI: At ‘ New Sys Name? You build the systems and groups then use as much memory as you need in the pool to store frequencies, talk group ID’s, and alpha tags. Selecting a Band Plan.

Most radios using this type of operation are limited to line-of-sight operation. This setting applies to all channels in the system.

Set Quick Key assigns quick key to a site and will be scanned when the key is turned on. Then see Creating Groups. Then see Creating Sites. Ignore – the scanner does not return to the control channel until the carrier drops.

If you are traveling at a speed greater than that specified, in the direction specified, and if you are within range of the set location, the scanner sounds an alert at 1.

Press twice to ‘unlock’ Function mode and resume. If you turn off all groups in a system you will not be able to turn any nearcat on and also see ‘ Nothing to Scan ‘. Off – any signal opens squelch. Some Motorola and EDACS systems covering a very large geographic area use multiple antenna sites that each operate on different frequencies and use the same talkgroup IDs for traffic.

800 xlt setup help

This deletes all beqrcat data. Searching- the process of searching for active frequencies in quick search, service, custom search, Close Call search, Search and Store, or Close Call Auto Store.

  KRAMER VP 502XL PDF

Make sure the power is turned off. What state, county, city, agencies, etc. Scanner Reset to initialize the scanner’s memory, turn off the scanner. Also, you can’t cancel Startup Configuration, i. When the scanner finds an active transmission, it checks to see if the frequency has already been stored in the system ‘ Memory Check ‘ in 800slt display. Set Attenuator conventional only.

At ‘ Select Comm Port ‘ scroll to the port the Slave scanner is using. Motorola trunking radios directly interpret them for their special functions, thus no difference is noticed by the person with the radio.

If no systems are programmed, or all systems or groups in a system are locked out or turned off, ‘ Nothing to Scan ‘ appears. To Edit Channel Options press Menu. You can also lock out this subfleet ID so you will not receive it. Then set up both scanners: Custom Search lets you search the scanner’s 10 programmed frequency ranges.

To hold on a CC hit press Hold. 800x,t

Set Delay Time for the system sets in seconds the amount of time the scanner stays on a channel after the transmission has ended before moving to the next channel. LTR systems work a little differently. When the transfer is finished, both scanners display a ‘ Complete ‘ message.