ASTM E/EM: Standard Practice for Design and Performance of Supported Laminated Glass Walkways. of breakage (POB) of 8/ from the appendix of ASTM E, these allowable stresses While ASTM E () does address point loads as design. testing to ASTM F Test Method. • Testing program 41kPa,. kPa-msec ASTM E Standard. Practice. – Calculation method. • Determine glass.

Author: Sarr Vobei
Country: Honduras
Language: English (Spanish)
Genre: History
Published (Last): 5 April 2017
Pages: 396
PDF File Size: 12.47 Mb
ePub File Size: 20.59 Mb
ISBN: 661-3-49317-700-5
Downloads: 10542
Price: Free* [*Free Regsitration Required]
Uploader: Faelkree

Glass is one of the most used materials in buildings and has been for the last years. While commercially popular, some types of modern building glass may represent a serious danger. Float glass was the most astk type of glass used in buildings until recent times. Depending on its age, condition and thickness, float glass can break and shatter under human impact.

When it shatters, float glass asmt into shards that are sharp and pointed.

These shards can easily cut flesh and tendons, and the results can be severe or even atsm. According to the National Safety Council, hundreds of people are injured each year through their encounter with broken float glass.

When someone impacts float glass, the danger is twofold. The first is the likelihood of being cut during the impact; the second involves the instincts of many people to pull their xstm, arm, or leg away from the glass.

As the injured person recoils, the pointed shards can make deep lacerations that can be life threatening. Glass safety standards were developed that aimed at curbing this trend.

First produced in Europe, wired glass was introduced to the United States in or around While not as strong as the later developed annealed or tempered glass, wired glass was used for over 50 years in windows in doors and along corridors, and those areas required to provide fire separation protection.

Written into fire and life safety codes for much of those 50 years, wired glass can still be found in buildings today. Wired glass is less strong than float glass. Under impact, body parts can break the glass, and the embedded wires present a significant risk of injury.

ICC Passes Two Glass Walkway Provisions

adtm The use of wired glass has faded with the introduction of axtm and tempered glass products but it is still present in many older buildings today.

Commonly referred to as safety glazing, heat strengthened, laminated, and tempered glass, as well as ceramic, plastic and polymer products are now commonly used glazing materials in areas subject to the likelihood of human impact.

These products are less likely to break when subjected to impact and less likely to cause serious injury if broken. Heat strengthened and tempered aatm break into rounded cubes which may still contain sharp edges, but do not form dagger-like shards. Laminated glass products may break, but are held together by an interlayer of plastic or polymer reducing the likelihood of exposure to sharp edges.


Building Glass & Premises Safety – Expert Article

But tempered glass and other types of safety glazing are not hazard free. Depending upon where and how they are used, even these products can be w2751. What are hazardous locations for glass and glazing? Model codes, including the International Building Code, define these areas as those subject to human impact. Generally, they are 2e751 areas surrounding a doorway and places where it is foreseeable that a person could walk and encounter glazing, such as patios, and fully glazed storefronts.

Shower and sauna enclosures and glass enclosures at some recreational and sports areas are also identified as impact hazard areas. Storefronts and glazed curtainwalls may not be reliably identified by people walking nearby and they can easily be confused with an open walking path.

Transparent glass walls where the glass cannot be easily distinguished from the surroundings should be made conspicuous to prevent impact injuries. Floor to ceiling storefronts, shopping malls, restaurants, office buildings, and other commercial environments often include these features. Without appropriate markings, people can unintentionally walk into these features and r2751 injured without breaking the glass. A common feature in commercial and retail environments, Glass guards and handrails require the same safety features as non-glass guards and handrails.

Impact resistance, breakage tolerance, deflection of the system, and the free area between components are all regulated by this e275 and asmt failure to meet any one of them can result in injury.

Section 2409 Glass in Walkways, Elevator Hoistways and Elevator Cars

Glass walkways, while less common, are also required to comply with a nationally recognized standard. ASTM E, Standard Practice for Design and Performance of Supported Glass Walkwaysprovides requirements for structural performance, markings for clarity and slip resistance for the design and construction of these features.

The use of glass in windows, doors, storefronts, along stairs or ramps and similarly glazed features do not have to be dangerous if relatively simple precautionary measures are taken to assist people in identifying and avoiding these hazardous e2571. Existing float glass can be covered e271 guards or a transparent wstm to prevent it from shattering and most glass can be easily removed and atm with an appropriate safety glazing material.

Glass can be a safe building component when used in compliance with recognized standards and protected from human impact, but injuries still regularly occur. Old float or wired glass still in use where modern standards require safety glazing products; improperly installed replacement glass panels and tempered or heat strengthened glass which fail during use; and inadequately marked or protected glass panels which cannot be reliably identified can all result in injury.

The premises safety experts at Robson Forensic have investigated many injuries involving broken glass, falling glass panels, and pedestrian collisions with doors, windows, and other partitions. Submit an inquiry e251 contact the author of asttm article to discuss your case and how we can assist.


Anthony is a Registered Architect with over twenty seven years of professional experience in the Architectural and Engineering Consultant industry. His expertise in facility design, construction, and architectural professional practice, along with his extensive experience in the premises safety aspects of the built environment, are applied to relevant forensic casework.

This article was developed in concert with other members of the Premises Safety practice group. For assistance determining which expert is f2751 qualified to investigate the specific technical aspects of your case, please contact your local Robson Forensic office or submit an inquiry through our website. Through video he e7251 a As a former awtm officer on the AIA National Ethics Council, and now a testifying expert in construction disputes, I have seen my share of In this article, architect and premises safety expert, Anthony Shinsky discusses various aspects of flooring that influence pedestrian safety.

Your message has been received – we will be in touch shortly. If you have specific questions or need immediate assistance, please contact us directly at Stay up to date with weekly communications from Robson Forensic – Substantive technical articles, safety practices across various industries, contact information from featured experts. Click here to join.

His discussion covers the various categories of glass, the use of glass in windows, doors, and partitions, and relevant safety standards. Types of modern glass include: It can be cut again. It breaks into sharp shards. A heavier form of this glass is float glass. Heat Strengthened Glass H. Glass is annealed glass that goes through a heating and cooling process designed to double its strength in comparison to ordinary annealed glass. Laminated Glass has two separate pieces of annealed, heat strengthened or tempered glass sandwiched around a layer of clear polyvinyl butaryl PVB.

One side can shatter from impact without the other side shattering, and, when the glass shatters, it does not delaminate into shards… Tempered Glass is created during manufacture by rapidly cooling the outer surfaces of the glass while the inner portion remains viscous. When tempered glass breaks, it fractures perpendicular to the plane of the surfacerather than parallel to it, resulting in small cubes that are less likely to cause significant injury… Float glass was the most common type of glass used in buildings until recent times.

Featured Expert Anthony J. What is a Safe Floor? Share this page by email. Or share socially on Facebook on Twitter on LinkedIn.