The APL series of high performance positive volt- age regulators are designed for use in applications requiring very low dropout voltage at 5Amp. APL Datasheet PDF Download – DUAL INPUT LOW DROPOUT REGULATOR, APL data sheet. ANPEC APL datasheet, DUAL INPUT LOW DROPOUT REGULATOR (1- page), APL datasheet, APL pdf, APL datasheet pdf, APL
|Country:||Saint Kitts and Nevis|
|Published (Last):||15 March 2004|
|PDF File Size:||6.89 Mb|
|ePub File Size:||17.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
Current limit is trimmed to ensure specified output cur. The thermal pad is soldered to the top VOUT plane which may be connected to internal or bottom Datasheett plane datashet vias to reduce the heat sink thermal resistance. Positive side of the reference voltage, which allows remote sensing to. For this purpose, the a;l1581 capacitors are.
Current limit is trimmed to ensure specified output cur- rent and controlled short-circuit current. Adjustable Version Assembly Adtasheet L: Supply pin of the control circuitry, which must be always higher than V OUT. MSL classification at lead-free peak reflow temperature. View PDF for Mobile. This region above the curve indicates minimum required ESR and capacitance to maintain stability.
The Datashdet can provide a output voltage at the range of. The superior dropout characteristics result in reducing heat dissipation compared to regular LDOs. A low-ESR solid tantalum and aluminum electrolytic ca. It is not necessary to use low-ESR capacitors. Ultra- low-ESR capacitors, such as ceramic chip capacitors, may promote unstable or under-damped transient response, but proper ceramic chip capacitors placed near loads can be used as decoupling capacitors.
Careful con- sideration must be given to all sources of thermal resis- tance from junction to ambient, including junction-to-case, case-to-heat sink interface, and heat sink resistance itself. The APL series of high performance positive volt.
The APL can provide a output voltage at the range of. The APL is available in both the through-hole and. Negative side of the reference voltage, which allows to use resistor divider. However, maximum junction temperature ratings should not be exceeded under continuous normal load conditions. For VIN pin, an aluminum.
(PDF) APL1581 Datasheet download
On-chip thermal limiting provides protection datassheet any combina- tion of overload that would create excessive junction temperature. The following chart shows a stable re.
Ordering and Datasehet Information. ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise. V OUT The output capacitors are also used to reduce the slew rate of load current and help the APL to minimize variations of the output voltage, improving transient response. Ordering and Marking Information. For fixed voltage devices this is the bottom of the resistor divider that sets. Remote Voltage Sensing Stability and Output Capacitors The circuit design of using the APL series requires an output capacitor as part of the device frequency compensation.
See Figure 3, the SOP-8P is a cost-effective package featuring a small size as a standard SOP-8 and a bottom thermal pad to datasheeet the thermal resistance of the package, datashret applicable to high current applications.
APL Datasheet PDF – Anpec Electronics
MSL classification at lead-free peak reflow temperature. Dropout at 5A in Dual Power. Halogen and Lead Free Device. A small bypass capacitor can be connected. The APL also provides excellent regulation over line, load, and tem- perature variations.
The APL is available in both the through-hole and. The APL series of high performance positive volt. Grounding and Output Sensing Cont. Therefore, the printed circuit board PCB forms a heat sink and dissipates heat into ambient air. Current limit is trimmed to ensure specified output cur. The circuit design of using the APL series requires. Halogen and Lead Free Device. The APL series have internal power and thermal.
The superior dropout characteristics result in reducing. ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise. However, the output ca. For this purpose, the low-ESR capacitors are recommended. The thermal pad is soldered to the top VOUT plane which. The APL can provide a output voltage at the range of 1. The superior dropout characteristics result in reducing. Home – IC Supply – Link. Lead Free Device G: